How to Attach a Lace Front Wig: Step-by-Step Guide for a Flawless Wig Install

Looking to secure your lace front wig for a natural, undetectable look that lasts all day? Whether you’re using liquid wig adhesive or wig tape, applying your lace front wig correctly is the key to achieving a flawless, long-lasting hold.

In this complete guide, you’ll learn how to attach a lace front wig, including prepping your hairline, applying adhesive, and removing the wig safely—all while protecting your natural hair and skin.

🧼 Step 1: Prep and Clean Your Hairline

Before applying your lace front wig, preparation is essential to ensure the adhesive sticks properly.

• Trim the Lace: Cut the lace close to the wig hairline, being careful not to cut any hair.
• Position the Wig: Place the wig on your head, making sure the lace sits slightly in front of your natural hairline to avoid contact between glue and your real hair.
• Clean the Skin: Wash your face and hairline area with a non-oily soap like Dial® or Irish Spring® to remove sweat, oils, and dirt.
• Apply Scalp Protector: Use a scalp protector spray or dab around the perimeter below your hairline. This helps prevent irritation and strengthens the adhesive bond, especially if you have oily or sensitive skin.

🧴 Step 2: Apply Wig Adhesive (Liquid or Tape)

Depending on your preference, choose either liquid wig glue or lace wig tape for securing your unit.

🔹 Option 1: Liquid Lace Wig Glue

Using liquid adhesive is ideal for long-term wear and a super-strong bond.

Instructions:

1. Use a thin brush or applicator to apply a light coat of glue along the edge of your hairline.
2. Use a cool blow dryer to speed up drying. The adhesive must become tacky (not wet!) before applying the wig.
3. Starting from the front hairline, press the lace down onto the sticky glue.
4. Hold and apply light pressure for at least 1 minute.
5. Continue pressing down the sides and nape.
6. Wait 15 minutes before styling to ensure the adhesive sets completely.

📝 Pro Tip: Never apply the wig while the glue is still wet—it will lift prematurely.

🔹 Option 2: Lace Wig Tape Adhesive

Wig tape is a great choice for beginners or quick installs and can be found in strips or rolls.

Instructions:

1. Cut and apply the double-sided wig tape around your hairline.
2. Press the tape onto your clean skin, just below your natural hairline.
3. Pin the wig hair back to keep it out of the way.
4. Peel off the tape backing to expose the top adhesive layer.
5. Starting at the forehead, press the wig into the tape, holding for 30–60 seconds.
6. Repeat for sides and back.

🔄 Step 3: Safely Remove Your Lace Front Wig

Removing your lace wig gently is crucial to protect your natural hair and your lace unit.

Recommended Products:

• C-22 Solvent
• Lace Release Spray
• 99% Isopropyl Alcohol

Removal Instructions:

1. Spray adhesive remover generously along the hairline.
2. Allow it to sit and loosen the adhesive naturally—never pull or rip!
3. Use a combination of remover and alcohol to gently dissolve any stubborn glue.
4. Once loose, roll off excess glue from both your scalp and the lace base.
5. Wash your skin gently and condition the lace for future use.

🎯 Final Tips for Flawless Lace Front Wig Application

• Always start with a clean, dry, and oil-free hairline.
• Use a scalp protector for sensitive or oily skin types.
• Don’t rush—let glue dry until tacky for best results.
• Practice makes perfect: you’ll develop your technique over time.

📌 Conclusion

Whether you use wig glue or tape, following the right application and removal process will give your lace front wig a secure, natural-looking hold. Bookmark this guide and refer back every time you want a flawless wig install!